Difference between revisions of "COVID"
(14 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | + | '''<big>COVID INFORMATION</big>''' | |
− | + | {{Note|[https://umassmed.edu/coronavirus/return-to-work-guidelines-for-employees-and-students/ UMMS Guidelines for Employee Return to Work]}} | |
+ | {{Note|[https://umassmed.edu/coronavirus/return-to-work-guidelines-for-laboratory-personnel/ COVID-19 Guidelines for Laboratory Personnel]}} | ||
− | + | There will soon be a vacant/occupied sign outside each microscope rooms. Please use them in addition to the calendar. | |
+ | |||
+ | == Scheduling == | ||
+ | |||
+ | Microscopes are only to be scheduled for half a day or for a full day at big.umassmed.edu. The calendar now defaults to full day. If you need to use a microscope for less than a day, start your microscope session on the hour, and end half-past an hour. For example, start at 9am, and end at 11:30am. This allows at least a 30 minute gap between users for proper air exchange to occur in the room. | ||
+ | |||
+ | {{Note|For multiple microscope rooms, only the main microscope maybe scheduled at a time. The additional microscopes has been removed from the calendar. }} | ||
+ | {{Note|Scheduling discipline must be adhered to for everyone's safety.}} | ||
== Cleaning == | == Cleaning == | ||
− | {{Warning|Assume the microscope and computers were not properly cleaned previously | + | The following will need to be done '''before''' starting your imaging session, and '''after''' you have finished. |
− | + | {{Warning|Assume the microscope and computers were not properly cleaned previously}} | |
− | |||
− | {{Warning| | + | {{Warning|Use only 70% Ethanol, applied to a napkin or Kimwipe, except for objectives which require lens paper. Do not spray directly on the microscope or electronics}} |
− | + | {{Warning|You should wear a fresh pair of gloves inside microscope room. Please dispose of them once you are outside of the microscope, and after the door has been shut}} | |
=== Power Switches === | === Power Switches === | ||
− | Assume all power switches are contaminated. You may elect to use gloves and/or wipe them down. If you don't use gloves, please | + | Assume all power switches and other high contact surfaces are contaminated. You may elect to use gloves and/or wipe them down. If you don't use gloves, please sanitize your hands immediately before and after touching any power switches. Keys to turn lasers on maybe difficult to clean but should be done. {{Note|Keys for lasers do not have to be turned off (and cleaned) after you have finished.}} |
− | === | + | === Computers === |
* Wipe the power button. | * Wipe the power button. | ||
* Wipe the tops of the keys of the keyboard. | * Wipe the tops of the keys of the keyboard. | ||
* Wipe the top and sides of the mouse. | * Wipe the top and sides of the mouse. | ||
* Wipe down the desk area around the keyboard and mouse. | * Wipe down the desk area around the keyboard and mouse. | ||
− | === | + | === Microscopes === |
− | * Wipe the | + | * Wipe the cap and sides of the oil bottle. |
− | * Wipe the left and right fine/ | + | * Wipe the left and right fine/coarse focus control knobs. |
− | * Wipe the stage surface, especially focusing on the areas you manipulate to insert a slide. | + | * Wipe the stage surface and stage control knobs, especially focusing on the areas you manipulate to insert a slide. |
* Wipe down the front body of the microscope, where your exhaled air would likely land. | * Wipe down the front body of the microscope, where your exhaled air would likely land. | ||
* Wipe down any optical table surface that you might place arms or hands. | * Wipe down any optical table surface that you might place arms or hands. | ||
* If equipped, wipe the remote focus control knob. | * If equipped, wipe the remote focus control knob. | ||
* If equipped, wipe down any control pads and/or stage control joysticks. | * If equipped, wipe down any control pads and/or stage control joysticks. | ||
− | * Confirm that the ocular | + | * Confirm that the ocular rubber eyecups are not in place. They should not be used. |
+ | |||
+ | {{Note|The above cleaning process should be done '''before''' and '''after''' using a shared microscope or shared computer.}} | ||
+ | |||
+ | == Assistance == | ||
+ | |||
+ | If you need help, email, text, voice call, or video call with Karl Bellve maybe done. If he has to enter a microscope room to solve an issue, he will wait until you have left the room or come in during off hours. | ||
+ | |||
+ | Contact Information: Karl.Bellve@umassmed.edu. |
Latest revision as of 18:29, 3 June 2020
COVID INFORMATION
There will soon be a vacant/occupied sign outside each microscope rooms. Please use them in addition to the calendar.
Scheduling
Microscopes are only to be scheduled for half a day or for a full day at big.umassmed.edu. The calendar now defaults to full day. If you need to use a microscope for less than a day, start your microscope session on the hour, and end half-past an hour. For example, start at 9am, and end at 11:30am. This allows at least a 30 minute gap between users for proper air exchange to occur in the room.
Cleaning
The following will need to be done before starting your imaging session, and after you have finished.
Power Switches
Assume all power switches and other high contact surfaces are contaminated. You may elect to use gloves and/or wipe them down. If you don't use gloves, please sanitize your hands immediately before and after touching any power switches. Keys to turn lasers on maybe difficult to clean but should be done.
Computers
- Wipe the power button.
- Wipe the tops of the keys of the keyboard.
- Wipe the top and sides of the mouse.
- Wipe down the desk area around the keyboard and mouse.
Microscopes
- Wipe the cap and sides of the oil bottle.
- Wipe the left and right fine/coarse focus control knobs.
- Wipe the stage surface and stage control knobs, especially focusing on the areas you manipulate to insert a slide.
- Wipe down the front body of the microscope, where your exhaled air would likely land.
- Wipe down any optical table surface that you might place arms or hands.
- If equipped, wipe the remote focus control knob.
- If equipped, wipe down any control pads and/or stage control joysticks.
- Confirm that the ocular rubber eyecups are not in place. They should not be used.
Assistance
If you need help, email, text, voice call, or video call with Karl Bellve maybe done. If he has to enter a microscope room to solve an issue, he will wait until you have left the room or come in during off hours.
Contact Information: Karl.Bellve@umassmed.edu.